ppm-series ? ppm02-s-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 ppm 02-s-xxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications input voltage range 85 ? 305 vac or 120 ? 430 vdc universal input frequency 47 ? 63 hz input (inrush) current 115 vac 230 vac 44 ma (5a, typ.) 25ma (11a, typ.) external input fuse (recommended) 1a / 300v slow blow output specifications voltage accuracy 5%, typ (6% @3.3 vout) line regulation (at full load) 2% load variation (10-100%) 5% ripple and noise (20mhz bandwidth) 100mv pk-pk short circuit protection continuous, auto recovery common specifications temperature range -25c to +70 c power derating 3.3% / c, min storage -40c to +85 c humidity (non condensing) 95%, max. switching frequency 100khz i/o isolation voltage 3000vac / 1min. emi / rfi conducted en55022, class b emc compliance esd rs eft surge cs pfm voltage dips, short and interruptions immunity iec/en 61000-4-2 contact8kv/air8kv perf. criteria b iec/en 61000-4-3 10v/m perf. criteria a iec/en 61000-4-4 2kv perf. criteria b iec/en 61000-4-5 1kv/2kv perf. criteria b iec/en 61000-4-6 10vr.m.s perf. criteria a iec/en 61000-4-8 10a/m perf. criteria a iec/en 610004-11 0%-70% perf. criteria b safety standards iec60950, en60950, ul60950 safety class class 2 case material ul94v-0 rated reliability calculated mtbf (mil-hdbk-217f) > 300,000 hrs weight ~ 20g mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the ppm series is a compact size power converter provided by peak . the features of this series are: wide input voltage, dc and ac all in one, high efficiency, high reliability, low loss, safety isol ation etc. they are widely used in industrial, office and civil equipments. em c and safety standards meet international standards iec61000, ul60950 and iec60950, and multicertificate is in processing. ppm-series 2 watt univ. 85-305vac (120-430vdc) single output over voltage protection (out) 3 kv ac i/o isolation low ripple and noise high efficiency rev.12-2014
ppm-series ? ppm02-s-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # p o w e r ( w ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) c a p a c i t o r l o a d f ( m a x . ) e f f i c i e n c y ( % ) single output ppm02-s-3r3elf 2 3.3 600 4000 65 PPM02-S-05ELF 2 5 400 4000 70 ppm02-s-09elf 2 9 222 2200 72 ppm02-s-12elf 2 12 167 2200 76 ppm02-s-15elf 2 15 133 1000 76 ppm02-s-24elf 2 24 82 680 78 if you need other specifications, please enquire. package / pinning / derating 15.24 (0.60) 22.20 (0.874) 0.6 (0.024) # single 1 ac (n) 2 ac (l) 3 - vout 4 + vout pin connections
ppm-series ? ppm02-s-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 app notes: parallel line measure typical application emc recommended circuit external capacitors typical value(unit: ? f) model c1 c2 tvs ppm02s3r3elf 1f/50v 220 smbj7.0a ppm02s05elf 1f/50v 220 smbj7.0a ppm02s09elf 1f/50v 120 smbj12a ppm02s12elf 1f/50v 120 smbj20 a ppm02s15elf 1f/50v 120 smbj20 a ppm02s24elf 1f/50v 68 smbj30 a note: 1. c1 is ceramic capacitor, it is used to filter hi gh frequency noise. c2 is electrolytic capacitor, i t is recommended to use high frequency and low impedance electrolytic capacitors . for capacitance and current of capacitor please r efer to manufactures datasheet. voltage derating of capacitor should be 80% or above. tvs is a recommended component to pro tect postcircuits (if converter fails). 2. for standard emc requirement, please refer to fi gure 1. if higher emc requirement, please refer to figure 3, recommended parameters are shown in the table below. recommend parameter for high er emc standard circuit components recommend parameter mov s14k350 cy3 2.2nf/400v cy4 2.2nf/400v cx 0.1 f/305vac lcm 10 mh ntc 5d-9 fuse 1a/300v, slow blow, it must be connected to fuse
|
